View HT2MOA3S20_4585359.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

HT2 MOA3 S20
HITAG 2 Chip Module
Preliminary Specification Revision 1.1 August 1997
TM
Specifications of the HT2 MOA3 S20
Rev. 1.1
1997-08-19
Table of Contents
1 Definitions .............................................................................................................................. 3
1.1 Objective of the Specifications ..................................................................................................................... 3 1.2 Definition of the Chip Module ..................................................................................................................... 3 1.3 Use of the Modules ...................................................................................................................................... 3
2 Specifications ......................................................................................................................... 4
2.1 Mechanical Properties ................................................................................................................................. 4 2.2 Materials ..................................................................................................................................................... 4 2.3 Temperature Range ..................................................................................................................................... 4 2.4 Storage Conditions ...................................................................................................................................... 5 2.5 Delivery Conditions..................................................................................................................................... 5 2.6 Electrical Specifications............................................................................................................................... 6
3 Drawing of the Chip Module HT2 MOA3 S20..................................................................... 7
3.1 Drawing of the Reel..................................................................................................................................... 7 3.2 Module outline suggestion ........................................................................................................................... 8 3.3 Splicing Specification .................................................................................................................................. 9
4 Coil Specifications................................................................................................................ 10 5 Functional Description of HITAG 2 ................................................................................... 12
5.1 Memory Organization................................................................................................................................ 12 5.2 Operation Modes and Configuration .......................................................................................................... 13 5.2.1 Modes of Operation............................................................................................................................ 13 5.2.2 Status Flow ........................................................................................................................................ 14 5.2.3 Configuration..................................................................................................................................... 15 5.3 Configuration of Delivered HITAG 2 Transponders................................................................................... 16 5.4 Definition of Passwords and Keys .............................................................................................................. 17
6 Quality Inspection ............................................................................................................... 18 7 Characterisation and Test of the Final Transponder......................................................... 19
7.1 Characterisation of the Transponder .......................................................................................................... 19 7.2 Final Test of the Transponder .................................................................................................................... 19
8 Ordering Information.......................................................................................................... 20 HITAGTM is a trademark of Philips Electronics N.V.
Ht2moa3.doc/HS
Page 2 of 22
Specifications of the HT2 MOA3 S20
Rev. 1.1
1997-08-19
1 Definitions
1.1 Objective of the Specifications
This specification lists the parameters to be fulfilled by the HITAG 2 chip module HT2 MOA3 S20 for contactless smart cards or similar transponders (as e.g. discs).
1.2 Definition of the Chip Module
A chip module is an electronically packaged chip covered with a globe top cap. The HT2 MOA3 S20 is above all used as card module, i.e. for further lamination into contactless smart cards according to ISO 10536.1. So the HITAG 2 chip module HT2 MOA3 S20 is best suited for customers that do not want to spend time with micro assembly and therefore start - e.g. ISO card production - with the HITAG 2 chip module.
1.3 Use of the Modules
The HITAG 2 modules are designed to be connected to a coil and then to be further processed by packaging into a transponder (e.g. lamination into an ISO smart card). Specific processing information for the coil-module connection and packaging is given in the specification. For production of contactless chip cards it is recommended to prepunch card foils to create a recess for the chip module in the card body.
Ht2moa3.doc/HS
Page 3 of 22
Specifications of the HT2 MOA3 S20
Rev. 1.1
1997-08-19
2 Specifications
2.1 Mechanical Properties
Width 7.55 mm (Proposed Punching Outline) Length 11.75 mm (Proposed Punching Outline) Overall Thickness Film Thickness Bondpad Size for Transponder Coil / Module Interconnection 0.45 mm 0.03 mm 0.16 mm 0.005 mm 1.9 x 3.5 mm Suitable for Welding/Soldering/ Conductive Gluing see also drawing in chapter 3
2.2 Materials
Tape Copper Plating Bond Plating Backside Plating Glob Top 110 m 35 m Ni / Au Ni / Au Filled Epoxy Thermal curing Glass epoxy ED copper Suitable for Al and Au wire bonding
2.3 Temperature Range
Operating Processing -25C to +85C 150C for 30 minutes For packed transponder, depending on type of package at a standard lamination pressure for contactless smart card plastic materials (e.g. PVC, PET, ...) on bond pads on bond pads
Welding Parameters Soldering Parameters
max. 25 ms @ 500 C max. 3 s @ 390 C
Ht2moa3.doc/HS
Page 4 of 22
Specifications of the HT2 MOA3 S20
Rev. 1.1
1997-08-19
2.4 Storage Conditions
Temperature Relative Humidity Duration 15 - 30 C 40 - 70 % 1 year
2.5 Delivery Conditions
Delivery Identification Date of ready for shipment, reel numbers, total quantity of good modules with the detail of good modules per reel, order number, product type, no supplier identification on reels, bags and boxes. Chip modules on reel approx. 15.000 to 20.000 pcs. per reel, tape width super 35 mm, pitch 9,5 mm, 2 rows 500 pcs . per bag Order-No. 3322 845 04881
Types of Delivery
single chip modules (bulk goods) Packing and Transport According to documentation "Packing Method Modules (reel)" "Packing Method Modules (singulated)" Bad Module Marking All bad modules (mechanical and electrical faults) must be punched by reject hole for customer Bad positions (reel): <20% Splicing Specifications Tape material: adhes. tape 15,5 +/- 0,7 mm, thermal resistance at <190C by < 100 cN tractive power and < 30 sec. duration. Identification label on the reel and on carton bag: - Product type - Number of the reel - Total number of positions - Number of good positions - Date of sealing (to be checked) - Two batches per reel only - Batch number indication (only coded, to be checked)
see drawings chapter 3
see drawings chapter 3
Labeling
Ht2moa3.doc/HS
Page 5 of 22
Specifications of the HT2 MOA3 S20
Rev. 1.1
1997-08-19
2.6 Electrical Specifications
Symbol Absolute Maximum Ratings Junction Temperature Input Peak Current Latch up Current ESD Operating Range Temperature Input Read Only Threshold 1) Voltage 3) Input Threshold Voltage Input Read Voltage Input Write Voltage Demodulator Range
3) 1) 3) 1) 3) 1) 3)
min
typ
max
Comment / Conditions
TJ IINpeak
-55C
140C 30 mA
100 mA 2 kV
MIL-STD 883D, Method 3023 MIL-STD 883D, Method 3015.7, Human Body
TA VIN,RO VIN,TH VIN,RD VIN,WR
-40C 2,8 Vp 3,1 Vp 3,5 Vp 3,7 Vp
85C 3,9 Vp 4,2 Vp 4,5 Vp 4,7 Vp
RThJunctionAmbient 30 K/W @ IINpeak = 30 mA start modulation in read only modes start modulation after SETCC read EPROM write EPROM
VDEM_R
2,0 Vp
4,0 Vp
VINHigh - VINLow @ VINHigh = 5,0 Vp 2) T0=8 s, TMOD=6*T0 VINLow 2,0 Vp VINLow 2,0 Vp
Modulator R_MOD linear 3) R_MOD nonlinear 3) Resonance Capacitor
3)
RMODL RMODNL
4,5 k 3,6 k
CResInit
189 pF
210 pF
231 pF
VIN = 4,0 Vp
EEPROM Write Current Read Current
4) 4)
IW IR Years Cycles 10 100.000
25 A 9 A
VDD = 2,8 V VDD = 2,8 V @ 55C
Data Retention Write Endurance
1) 2)
VIN = VIN1 - VIN2 ... voltage between connection pads VINHigh VINLow TMOD input voltage before modulation input voltage during modulation duration of the modulation
3) 4)
@ Ri = 10 k resistance of measurement equipment tested on silicon level
Ht2moa3.doc/HS
Page 6 of 22
Specifications of the HT2 MOA3 S20
Rev. 1.1
1997-08-19
3 Drawing of the Chip Module HT2 MOA3 S20
3.1 Drawing of the Reel
Ht2moa3.doc/HS
Page 7 of 22
Specifications of the HT2 MOA3 S20
Rev. 1.1
1997-08-19
3.2 Module outline suggestion
Ht2moa3.doc/HS
Page 8 of 22
Specifications of the HT2 MOA3 S20
Rev. 1.1
1997-08-19
3.3 Splicing Specification
Ht2moa3.doc/HS
Page 9 of 22
Specifications of the HT2 MOA3 S20
Rev. 1.1
1997-08-19
4 Coil Specifications
The HITAG 2 chip module has to be connected to a coil whose parameters are briefly described in the following.
Equivalent circuit of the transponder
Xpc
Rpc
Cp
Uc
Cchip
Rchip
Uc fres Xpc Rpc Cp Cchip Rchip fresc Lpc Lpc Cchip Rpc fresc
... ... ... ... ... ... ... ... = = = > >
voltage at the connection pads resonant frequency of the transponder parallel reactance of the coil (f = 125 kHz) parallel resistance of the coil (f = 125 kHz) parasitic capacitance of the package capacitance of the chip (Uc > 4 Vpp) resistance of the chip self resonant frequency of the coil Xpc/2f (f = 125 kHz) 7.72 mH x % (Cp = 0, x depends on the coil production process) 210 pF 10 % 45 k[ 750 kHz
Note: The parasitic capacitance of the package (Cp) must be considered. fres = 1 1 = 125 kHz L pc = 2 2 (Cchip + Cp).Lpc (2fres ) Cchip + C p
(
)
Typical values for Cp hot laminated cards: moulded tags:
Cp = 1.5 pF Cp = 6.0 pF
Ht2moa3.doc/HS
Page 10 of 22
Specifications of the HT2 MOA3 S20
Rev. 1.1
1997-08-19
For a rough estimation ( 10 %) of the number of coil windings following formula can be used. It is assumed that the winding is done in circular form.
N=
L
1 ,8 5
2 U ln (
u ) d
N L U d u
... number of windings ... inductance [nH] ... average coil circumference [cm] ... copper diameter [mm] ... average coil circumference [mm]
For fine tuning a measurement of the inductance and an according adjustment of the number of windings is necessary. This process always needs some iterations.
Ht2moa3.doc/HS
Page 11 of 22
Specifications of the HT2 MOA3 S20
Rev. 1.1
1997-08-19
5 Functional Description of HITAG 2
5.1 Memory Organization
The memory of the transponder consists of 256 bits EEPROM memory and is organized in 8 pages with 32 bits each. Depending on the operation mode the EEPROM is organized as described in the following.
Crypto Mode:
Page 0 1 2 3 4 5 6 7 Content Serial Number 32 bit "KEY LOW" 16 bit " KEY HIGH", 16 bit reserved 8 bit Configuration, 24 Bit Password TAG read/write page read/write page read/write page read/write page
Password Mode:
Page 0 1 2 3 4 5 6 7 Content Serial Number Password RWD reserved 8 bit Configuration, 24 bit Password TAG read/write page read/write page read/write page read/write page
Ht2moa3.doc/HS
Page 12 of 22
Specifications of the HT2 MOA3 S20
Rev. 1.1
1997-08-19
5.2 Operation Modes and Configuration
With the Configuration Byte the operation mode and the access rights to the memory can be selected. During Power-Up of the transponder the Configuration Byte is read from the transponder's EEPROM.
If you change the configuration, keys or passwords, you have to place the transponder directly on the antenna or hold it directly to it (0-distance)! In order to avoid any errors do not move the transponder during this write process and be sure that you are in a safe environment without electrical noise.
5.2.1 Modes of Operation
The HITAG 2 can be operated in several modes.
Crypto Mode:
Mode for writing or reading the transponder with encrypted data transmission.
Password Mode:
Mode for writing or reading the transponder with plain data transmission. A password check is performed.
Public Mode A (Manchester):
Read only mode emulating Philips Semiconductors MIRO transponders resp. EM H400x transponders. The 64 bits of the user Pages 4 and 5 are cyclically transmitted to the read/write device.
Public Mode B (Biphase):
Read only mode according to ISO standards 11784 and 11785 for animal identification. The 128 bits of the user Pages 4 to 7 are cyclically transmitted to the read/write device.
Public Mode C (Biphase):
Read only mode emulating the read operation of the PCF793X (with a slightly different Program Mode Check). In the Public Mode C the 128 bits of the user Pages 4 to 7 are cyclically transmitted to the read/write device.
Ht2moa3.doc/HS
Page 13 of 22
Specifications of the HT2 MOA3 S20
Rev. 1.1
1997-08-19
5.2.2 Status Flow
After entering the RF-field the transponder waits for a command to start the authentication. After issuing this command the mutual authentication takes place, followed by read- and write commands. In password mode the data transfer occurs plain, in crypto mode data are encrypted. The halt mode can be entered for muting a transponder. If the transponder is configured in one of the public modes, these modes are entered automatically after a certain waiting time and data pages are sent cyclically to the read/write device. By issuing the command to start the authentication during the waiting time also public mode transponders can be brought into the authorized state.
Ht2moa3.doc/HS
Page 14 of 22
Specifications of the HT2 MOA3 S20
Rev. 1.1
1997-08-19
5.2.3 Configuration
The Configuration Byte is represented by the first 8 bits of Page 3 of the transponder memory.
Configuration Byte:
7 6 5 4 3 2 1 0 0: Manchester Code 1: Biphase Code Bit 2 Bit 1 Version 0 0
Coding
Public Mode biphase B 0 1 Public Mode manchester depending on bit 0 A 1 0 Public Mode C biphase depending on bit 0 1 1 HITAG 2 depending on bit 0 depending on bit 0 0: password mode 1: crypto mode 0: PAGE 6 and 7 read/write 1: PAGE 6 and 7 read only 0: PAGE 4 and 5 read/write 1: PAGE 4 and 5 read only THE SETTING OF THIS BIT IS OTP ! 0: PAGE 3 read/write 1: PAGE 3 read only; Configuration Byte and Password TAG fixed THE SETTING OF THIS BIT IS OTP ! 0: PAGE 1 and 2 read/write 1: PAGE 1 no read/no write PAGE 2 read only (when transponder is in password mode) PAGE 2 no read/no write (when transponder is in crypto mode)
Coding in HITAG 2-Operation depending on bit 0
Configuration Byte / Bit 6:
Bit 6 = `0': Page 3 is read/write. Bit 6 = `1': Page 3 can only be read. This process is irreversible ! ATTENTION: Do not set Bit 6 of the Configuration Byte to `1' before having written the final data into Page 3 (including the Configuration Byte and Password TAG) of the transponder.
Configuration Byte / Bit 7:
Bit 7 = `0': Pages 1 and 2 are read/write. Bit 7 = `1': Pages 1 and 2 are locked against writing. This process is irreversible ! ATTENTION: Do not set Bit 7 of the Configuration Byte to `1' before having written the final data into Pages 1 and 2 of the transponder.
Ht2moa3.doc/HS
Page 15 of 22
Specifications of the HT2 MOA3 S20
Rev. 1.1
1997-08-19
Standard values for the Configuration Byte:
Password Mode: Crypto Mode: Public Mode A: Public Mode B: Public Mode C: 0x06 0x0E 0x02 0x00 0x04
5.3 Configuration of Delivered HITAG 2 Transponders
HITAG 2 transponders are delivered with the following configuration by Philips Semiconductors: Unique Serial Number: Serial Number: Read Only Configuration Byte: 0x06:
-
fixed
Password Mode (Manchester Code) Page 6 and 7 read/write Page 4 and 5 read/write Page 3 read/write Page 1 and 2 read/write
-
can be changed can be changed can be changed can be changed can be changed
Values for Transport Passwords, Transport Keys: Password RWD: 0x4D494B52 (= MIKR) Password TAG: 0xAA4854 Key Low: 0x4D494B52 (= MIKR) Key High: 0x4F4E (= ON) RECOMMENDATION: Before delivering transponders to end users, Pages 1 to 3 should be locked (set Configuration Byte / Bit 6 to `1' for Page 3 and set Configuration Byte / Bit 7 to `1' for Pages 1 and 2).
Ht2moa3.doc/HS
Page 16 of 22
Specifications of the HT2 MOA3 S20
Rev. 1.1
1997-08-19
5.4 Definition of Passwords and Keys
Keys are cryptographic codes, which determine data encryption during data transfer between read/write device and transponder. They are used to select a HITAG 2 transponder in Crypto Mode. The 16 bit KEY HIGH and 32 bit KEY LOW form one 48 bit key which has to be identical on both the transponder and the read/write device. Passwords are needed to select a HITAG 2 transponder in Password Mode. There is one pair of passwords (Password TAG, Password RWD) which has to be identical both on the transponder and the read/write device. Password TAG: Password that the transponder sends to the read/write device and which may be verified by the latter (depending on the configuration of the read/write device). Password that the read/write device sends to the transponder and which is checked for identity by the latter.
Password RWD:
It is important that the following values are in accordance with each other, i.e. the respective data on the read/write device and on the transponder have to be identical pairs. HITAG 2 in Password mode: on the on the read/write transponder device Password RWD Password RWD as an option (depending on the configuration of the read/write device): Password TAG Password TAG HITAG 2 in Crypto mode: on the read/write device KEY LOW KEY HIGH on the transponder KEY LOW KEY HIGH
as an option (depending on the configuration of the read/write device): Password TAG Password TAG The passwords and keys are predefined by Philips Semiconductors by means of defined Transport Passwords and a Transport Key. They can be written to, which means that they can be changed (see also Chapter "Configuration of Delivered HITAG 2 Transponders"). ATTENTION: Passwords and Keys only can be changed if their current values are known!
Ht2moa3.doc/HS
Page 17 of 22
Specifications of the HT2 MOA3 S20
Rev. 1.1
1997-08-19
6 Quality Inspection
Quality inspection is performed with statistical quality control according to ISO 2859 part 1, with AQL1.0.
Optical Properties scratches, according to the reference sample encapsulation failures, catalogue gold discolouration, delamination measured with gauge measured with gauge measured with micrometer at the center of the transfer mould cap basic read/write operations
Geometrical Properies width length overall thickness Electrical Properties Shipment Quantity Packing and Labeling operation
Ht2moa3.doc/HS
Page 18 of 22
Specifications of the HT2 MOA3 S20
Rev. 1.1
1997-08-19
7 Characterisation and Test of the Final Transponder
7.1 Characterisation of the Transponder
The parameters recommended to be characterised for the transponder are:
Parameter Resonant frequency Threshold value Threshold value for READ fres BTH BRD Comment Transponder does not modulate Resonant frequency @ Tamb = 22C, @ BTH Start of modulation Command READ_PAGE OK Command WRITE_PAGE OK
Threshold value for WRITE BWR
For the measurement of these parameters we recommend to use the test equipment available from SCEMTEC, Marienheide-Rodt, Germany (Transponder Measurement System STM-1). This device also supports functional testing (besides parameter testing). Therefore it can also be used as production test equipment for the final transponder test. For further information please contact Scemtec GmbH.
7.2 Final Test of the Transponder
In addition to the equipment described in the previous chapter Philips Semiconductors offers a device for a final functional test of transponders, the HITAGTM Test System HT OT490. Parameter tests are not supportet by this device. Basic flow for production and test: 1. Assembly of transponders 2. Functional test and final test of the EEPROM Since the Keys and Logdata are changed during final test the Configuration and personalization must take place after the final test. The final test is disabled (not reversible) by setting the Tag-test mode bit to 0.
For the final test of transponders we recommend to use the HITAGTM Test System HT OT490 of Philips Semiconductors or the Transponder Measurement System STM-1 of Scemtec.
Ht2moa3.doc/HS
Page 19 of 22
Specifications of the HT2 MOA3 S20
Rev. 1.1
1997-08-19
8 Ordering Information
Type Name HT2 MOA3 S20/E/3 HT2 MOA3 S20/E/1 Description HITAG 2 S20 Chip Module, reel HITAG 2 S20 Chip Module, bulk Ordering Number 9352 600 62118
9352 602 19122
Ht2moa3.doc/HS
Page 20 of 22
Specifications of the HT2 MOA3 S20
Rev. 1.1
1997-08-19
Definitions
Data sheet status Objective specification This data sheet conta ins ta rget o r goal spec ifications for product deve lopment. Preliminary specification This data sheet conta ins p reliminary data; supp lementary data may be pub lished later. Product spec ification Limiting values Limiting va lues g iven are in acco rdance with the Abso lute Maximum Rating Syste m (IEC 134). Stress above one o r more of the limiting va lues may cause pe rmanent da mage to the dev ice. These are stress ratings on ly and ope ration of the dev ice at these o r at any othe r cond itions above those g iven in the Characteristics sect ion of the spec ification is not implied. Exposu re to limiting va lues for extended pe riods may aff ect dev ice reliab ility. Application information Where application information is given, it is adv isory and does not form part of the spec ification. This data sheet conta ins final product spec ifications.
Life support applications
These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so on their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such improper use or sale.
Ht2moa3.doc /HS
Page 21 of 22
Philips Semiconductors - a worldwide company
Argentina: see South America Australia: 34 Waterloo Road, NORTHRYDE, NSW 2113, Tel. +612 9805 4455, Fax. +612 9805 4466 Austria: Computerstrae 6, A-1101 WIEN, P.O.Box 213, Tel. +431 60 101, Fax. +431 30 101 1210 Belarus: Hotel Minsk Business Centre, Bld. 3, r.1211, Volodarski Str. 6, 220050 MINSK, Tel. +375172 200 733, Fax. +375172 200 773 Belgium: see The Netherlands Brazil: see South America Bulgaria: Philips Bulgaria Ltd., Energoproject, 15th floor, 51 James Bourchier Blvd., 1407 SOFIA Tel. +3592 689 211, Fax. +3592 689 102 Canada: Philips Semiconductors/Components, Tel. +1800 234 7381 China/Hong Kong: 501 Hong Kong Industrial Technology Centre, 72 Tat Chee Avenue, Kowloon Tong, HONG KONG, Tel. +85223 19 7888, Fax. +85223 19 7700 Colombia: see South America Czech Republic: see Austria Denmark: Prags Boulevard 80, PB 1919, DK-2300 COPENHAGEN S, Tel. +4532 88 2636, Fax. +4531 57 1949 Finland: Sinikalliontie 3, FIN-02630 ESPOO, Tel. +3589 61 5800, Fax. +3589 61 580/xxx France: 4 Rue du Port-aux-Vins, BP 317, 92156 SURESNES Cedex, Tel. +331 40 99 6161, Fax. +331 40 99 6427 Germany: Hammerbrookstrae 69, D-20097 HAMBURG, Tel. +4940 23 53 60, Fax. +4940 23 536 300 Greece: No. 15, 25th March Street, GR 17778 TAVROS/ATHENS, Tel. +301 4894 339/239, Fax. +301 4814 240 Hungary: see Austria India: Philips INDIA Ltd., Shivsagar Estate, A Block, Dr. Annie Besant Rd. Worli, MUMBAI 400018, Tel. +9122 4938 541, Fax. +9122 4938 722 Indonesia: see Singapore Ireland: Newstead, Clonskeagh, DUBLIN 14, Tel. +3531 7640 000, Fax. +3531 7640 200 Israel: RAPAC Electronics, 7 Kehilat Saloniki St., TEL AVIV 61180, Tel. +9723 645 0444, Fax. +9723 649 1007 Italy: Philips Semiconductors, Piazza IV Novembre 3, 20124 MILANO, Tel. +392 6752 2531, Fax. +392 6752 2557 Japan: Philips Bldg. 13-37, Kohnan 2-chome, Minato-ku, TOKYO 108, Tel. +813 3740 5130,Fax. +813 3740 5077 Korea: Philips House, 260-199, Itaewon-dong, Yonsan-ku, SEOUL, Tel. +822 709 1412, Fax. +822 709 1415 Malaysia: No. 76 Jalan Universiti, 46200 PETALING JAYA, Selangor, Tel. +60 3750 5214, Fax. +603 757 4880 Mexico: 5900 Gateway East, Suite 200, EL PASO, Texas 79905, Tel. +9 5800 234 7381 Middle East: see Italy Netherlands: Postbus 90050, 5600 PB EINDHOVEN, Bldg. VB, Tel. +3140 27 82785, Fax +3140 27 88399 New Zealand: 2 Wagener Place, C.P.O. Box 1041, AUCKLAND, Tel. +649 849 4160, Fax. +649 849 7811 Norway: Box 1, Manglerud 0612, OSLO, Tel. +4722 74 8000, Fax. +4722 74 8341 Philippines: Philips Semiconductors Philippines Inc., 106 Valero St. Salcedo Village, P.O.Box 2108 MCC, MAKATI, Metro MANILA, Tel. +632 816 6380, Fax. +632 817 3474 Poland: Ul. Lukiska 10, PL 04-123 WARSZWA, Tel. +4822 612 2831, Fax. +4822 612 2327 Portugal: see Spain Romania: see Italy Russia: Philips Russia, Ul. Usatcheva 35A, 119048 MOSCOW, Tel. +7095 247 9145, Fax. +7095 247 9144 Singapore: Lorong 1, Toa Payoh, SINGAPORE 1231, Tel. +65350 2538, Fax. +65251 6500 Slovakia: see Austria Slovenia: see Italy South Africa: S.A. Philips Pty Ltd., 195-215 Main Road Martindale, 2092 JOHANNESBURG, P.O.Box 7430 Johannesburg 2000, Tel. +2711 470 5911, Fax. +2711 470 5494 South America: Al. Vicente Pinzon, 173 - 6th floor, 04547-130 Sao Paulo, SAO PAULO - SP, Brazil, Tel. +5511 821 2333, Fax. +5511 829 1849 Spain: Balmes 22, 08007 BARCELONA, Tel. +343 301 6312, Fax. +343 301 4107 Sweden: Kottbygatan 7, Akalla, S-16485 STOCKHOLM, Tel. +468 632 2000, Fax. +468 632 2745 Switzerland: Allmendstrae 140, CH-8027 ZURICH, Tel. +411 488 2686, Fax. +411 481 7730 Taiwan: Philips Taiwan Ltd., 2330F, 66, Chung Hsiao West Road, Sec. 1, P.O.Box 22978, TAIPEI 100, Tel. +8862 382 4443, Fax. +8862 382 4444 Thailand: Philips Electronics (Thailand) Ltd., 209/2 Sanpavuth-Bangna Road Prakanong, BANGKOK 10260, Tel. +662 745 4090, Fax. +662 398 0793 Turkey: Talapasa Cad. No. 5, 80640 GULTEPE/ISTANBUL, Tel. +90212 279 2770, Fax. +90212 282 6707 Ukraine: Philips Ukraine, 4 Patrice Lumumba Str., Building B, Floor 7, 252042 KIEV, Tel. +38044 264 2776, Fax. +38044 268 0461 United Kingdom: Philips Semiconductors Ltd., 276 Bath Road, Hayes, MIDDLESEX UM3 5BX, Tel. +44181 730 5000, Fax. +44181 754 8421 United States: 811 Argues Avenue, SUNNYVALE, CA94088-3409, Tel. +1800 234 7381 Uruguay: see South America Vietnam: see Singapore Yugoslavia: Philips, Trg N. Pasica 5/v, 11000 BEOGRAD, Tel. +38111 625 344, Fax. +38111 635 777
Philips Semiconductors, Mikron-Weg 1, A-8101 Gratkorn, Austria Fax: +43 / 3124 / 299 - 270
For all other countries apply to: Philips Semiconductors, Marketing & Sales Communications, Building BE-p, P.O.Box 218, 5600 MD EINDHOVEN, The Netherlands, Fax: +3140 27 24825 (c) Philips Electronics N.V. 1996 All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without any notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent- or other industrial or intellectual property rights. Internet: http://www.semiconductors.philips.com
SCB52

▲Up To Search▲

Price & Availability of HT2MOA3S20

	To Download HT2MOA3S20 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .